Shop headings: New Spares | Used Spares | Accessories | Brands
Clutch thrust bearing complete, sits in recess in rear gearbox casing.
Not suitable for early 4 speed gearboxes unless modified as per chapter 9 of Guzziology. Also known as Guzzi ref. 2A000376
2 in stock
12087001-z 12087001 GU12087001 12 08 70 01
1208 7001 1208.7001 12.08.70.01
£14.90
INC VAT
£12.42 EX VAT
Steel intermediate clutch plate
2 in stock
12082300-z 12082300 GU12082300 12 08 23 00
1208 2300 1208.2300 12.08.23.00
£28.00
INC VAT
£23.33 EX VAT
Rubber cover for Domino clutch lever and choke cable
Clutch cable rubber
2 in stock
27663815 GU27663815 27 66 38 15
2766 3815 2766.3815 27.66.38.15
£8.40
INC VAT
£7.00 EX VAT
Clutch pushrod for RAM clutch which is 5mm longer than the standard version. This may be needed when fitting a RAM clutch kit to give extra room for adjustment
2 in stock
£37.30
INC VAT
£31.08 EX VAT
External clutch operating lever pivot for gearbox end cover
Superceded to Guzzi ref. 2A000384
1 in stock
95780271 GU95780271 95 78 02 71
9578 0271 9578.0271 95.78.02.71
£21.00
INC VAT
£17.50 EX VAT
Clutch cable
replaces Guzzi ref. 30093011
1 in stock
30093000-z 30093000 GU30093000 30 09 30 00
3009 3000 3009.3000 30.09.30.00
£16.60
INC VAT
£13.83 EX VAT
Clutch plate kit consisting of 2 x friction plates, 1 x intermediate plate, deep splined clutch centre / boss and tabbed lock washer (not shown). For models with the early type shallow spline plates this is a worthwhile upgrade kit to the better deep splined centre and plates. Clutch plate alignment tool also available, see TOA30510. Suitable for all 5 speed dual plate clutch models
Save £20 on the cost of these components if bought seperately. Does not include clutch springs (see CLA13100). Thicker side of each friction plate should face transmission
1 in stock
£186.50
INC VAT
£155.42 EX VAT
Black Domino clutch lever
Replaces Guzzi ref. 27606715. See CLA30700 for polished version of this lever or CLA11342 for a span adjustable lever
1 in stock
27605715-z 27605715 GU27605715 27 60 57 15
2760 5715 2760.5715 27.60.57.15
Also fits Cagiva T4 350, Morini 350 Excalibur, Morini 501 Excalibur
£18.00
INC VAT
£15.00 EX VAT
Tool for clutch centre gear nut
Half inch socket drive. This is a cheaper aftermarket tool- see TOA14903 for original factory item
1 in stock
14912603 GU14912603 14 91 26 03
1491 2603 1491.2603 14.91.26.03
£39.00
INC VAT
£32.50 EX VAT
Dimensions:
1330mm outer length, 87mm free length, 9.9mm barrel nipple, 9.9mm barrel nipple, 9.7mm OD at clutch adjuster
Clutch cable for models with Magura switchgear
We advise you to measure your existing cable before ordering in case you have a non standard set up.
This part is available by special order, request a quote
28093011 GU28093011 28 09 30 11
2809 3011 2809.3011 28.09.30.11
£21.00
INC VAT
£17.50 EX VAT